Families

Normally, the electronics for reading the load sensor are positioned on the cabin roof, so that is where the calibration procedure has to be conducted. This means the technician has to take care not to include their own weight in the measurements. It also means that for any information about the weight in the cabin you always have to climb onto the roof. In our system, on the other hand, the load sensor reading electronics are still positioned on the cabin roof, but they are connected to the control panel. So, all operations (calibrations, cabin weight readings, fault diagnoses etc.) are carried out from our Smart-Chopper board, i.e. the control panel.

Under certain usage conditions, all lifts behave like energy generators. Two of these are the most favourable usage conditions: an empty cabin moving upwards or a full cabin moving downwards. In lifts with a traditional power supply, the energy generated under the conditions described above is wasted as heat by so-called braking resistors. This produces no benefits in terms of energy savings and consequent cost savings. As the energy required for the normal operation of our lifts is provided by batteries, under the conditions described above, these batteries accumulate any energy generated. This results in cost savings as the energy produced free of charge is used later to power the lift. Our lifts also have the option of being powered by a photovoltaic panel (SOL-ARE technology), which makes the lift even more efficient and increasingly independent from the national grid.

Our SOL-ARE technology optimises battery charging using the solar energy produced by a photovoltaic panel. The system automatically selects the ideal energy source (grid or photovoltaic panel) in order to minimize the amount of energy drawn from the grid, right down to a consumption level of ZERO.

The main power supply for our ARE systems is based on the use of lead-acid batteries, which are widely used in the automotive world. They guarantee a long service life, low costs and excellent performance. Like all batteries, they have a lifecycle, which is long and can be replaced for a limited cost.

Yes, all our lifts feature soft arrivals and departures. The silence achieved by our ARE SMART-POWER technology gives lift passengers a pleasant sensation of comfort throughout every run.

With the batteries charged and under optimal usage conditions, up to 60 runs can be made. This ensures efficient service even during a blackout.

In this case, Switch mode* is activated, i.e. the lift’s power supply shifts from batteries to mains, and the passenger is informed with an illuminated icon. The lift moves more slowly so it remains within the parameters of the electricity meter installed until the required battery charge level is reached.

* in switch mode the power used is 1200W and 1500W during rapid recharging. These values refer to a system with a load capacity of 450kg at a speed of 0.15m/s

Yes, ZEN-0 has a higher speed that can reach up to 0.8 m/s.

Normally, the electronics for reading the load sensor are positioned on the cabin roof, so that is where the calibration procedure has to be conducted. This means the technician has to take care not to include their own weight in the measurements. It also means that for any information about the weight in the cabin you always have to climb onto the roof. In our system, on the other hand, the load sensor reading electronics are still positioned on the cabin roof, but they are connected to the control panel. So, all operations (calibrations, cabin weight readings, fault diagnoses etc.) are carried out from our Smart-Chopper board, i.e. the control panel.

Our home lifts can guarantee up to 45 insertions per hour

Guides made of folded sheet metal offer considerable advantages:

Lightweight and with a maximum length of 2400 mm, they can be moved easily both during transport (they are packed in the mechanism box) and above all during assembly. They can be located inside any lift well without difficulty, even existing ones with parapets on the door side.
Unlike traditional electrical systems, which have arch and counterweight guides, using our guides on these systems allow both the cabin arch and the counterweight to move, which reduces assembly times.
Both the arch and the counterweight move along these guides on rollers. This means we do not need to use lubricants, like oils, and comfort and silence are guaranteed.
Superior style. Our guides are considerably more stylish than traditional guides. If a request is made to paint the cableway mechanisms along with all the lift’s metal parts, the guides are powder-painted too, which creates an extremely stylish effect.

The batteries are monitored by a system that checks their status and stops the lift when the batteries are not sufficiently charged. If this happens during a run, the system ends the run and remains stopped at that floor while it recharges. As soon as the batteries are sufficiently charged, the system starts working normally again. We can assure the customer that this type of situation occurs only very rarely because the batteries are sized according to a number of insertions per hour that the lift is unlikely to ever perform.

The gearbox is fitted with a speed limiter/safety gear system similar to the A3 amendment devices on lifts. When the system is stopped, the cabin and counterweight cannot move, which ensures that maintenance technicians can enter the pit in total safety when making repairs.

To achieve the highest level of sustainability, we have also researched how to dispose of batteries at the end of their lifecycle. Our approach is to use procedures that ensure the lowest possible environmental impact. Today, thanks to the development of new technologies, spent batteries can be disposed of in specialised and certified centres. This avoids any environmental risk and is, above all, in line with circular economy principles. In fact, the spent batteries are taken to centres specialised in recycling all the materials inside them. This involves subjecting them to a three-step process of:

Crushing.
Melting.
Refining.

At the end of the process, the pure metal is ready to be used again

for any application, including the production of new batteries.This recycling process allows the lead to be recovered with minimal environmental impact.

No, according to the Machinery Directive 2006/42/EC, the speed of home lifts in EU countries cannot exceed 0.15m/s. In countries outside the European Union this speed can reach up to 0.3m/s

A battery-powered lifting system guarantees high levels of energy efficiency, thanks to its low consumption of electrical energy from the national grid and its recovery system that stores energy in the batteries during operation, so it can be used in subsequent runs. From this point of view, battery power offers system users greater safety as it allows the lift to be used even in the event of a blackout.

Under certain usage conditions, all lifts behave like energy generators. Two of these are the most favourable usage conditions: an empty cabin moving upwards or a full cabin moving downwards. In lifts with a traditional power supply, the energy generated under the conditions described above is wasted as heat by so-called braking resistors. This produces no benefits in terms of energy savings and consequent cost savings. As the energy required for the normal operation of our lifts is provided by batteries, under the conditions described above, these batteries accumulate any energy generated. This results in cost savings as the energy produced free of charge is used later to power the lift. Our lifts also have the option of being powered by a photovoltaic panel (SOL-ARE technology), which makes the lift even more efficient and increasingly independent from the national grid.

The batteries are monitored by a system that checks their status and stops the lift when the batteries are not sufficiently charged.

If this happens during a run, the system ends the run and remains stopped at that floor while it recharges. Then, when the batteries are sufficiently charged, the system starts working normally again. This type of situation occurs only very rarely because the batteries are sized according to a number of insertions per hour that the lift is unlikely to ever perform.

The main power supply for our lifts is based on the use of lead-acid batteries, which are widely used in the automotive world. They guarantee a long service life, low costs and excellent performance. Like all batteries, they have a lifecycle, which is long and can be replaced for a limited cost.

With the batteries charged and under optimal usage conditions, up to 60 runs can be made. This ensures efficient service even during a blackout.

Our SOL-ARE technology optimises battery charging using the solar energy produced by a photovoltaic panel. The system automatically selects the ideal energy source (grid or photovoltaic panel) in order to minimize the amount of energy drawn from the grid, right down to a consumption level of ZERO.

Yes, all our lifts feature soft arrivals and departures.

The silence achieved by our ARE SMART-POWER technology gives lift passengers a pleasant sensation of comfort throughout every run.

A battery-powered lifting system guarantees high levels of energy efficiency, thanks to its low consumption of electrical energy from the national grid and its recovery system that stores energy in the batteries during operation, so it can be used in subsequent runs. From this point of view, battery power offers system users greater safety as it allows the lift to be used even in the event of a blackout.

No, according to the Machinery Directive 2006/42/EC, the speed of home lifts in EU countries cannot exceed 0.15m/s.

The minimum distance required between the floor and ceiling of the top floor (technically called “headroom”) is just 2000 mm. This makes MINIWATT the ideal solution for all environments like attics or lofts where a traditional lift cannot be installed.

No, a traditional 2000 mm high door can also be installed.

Under certain usage conditions, all lifts behave like energy generators. Two of these are the most favourable usage conditions: when the empty lift moves upwards or the full lift moves downwards. In lifts with a traditional power supply, the energy generated under the conditions described above is wasted as heat by so-called braking resistors. This produces no benefits in terms of energy savings and consequent cost savings. As the energy required for the normal operation of our lifts is provided by batteries, under the conditions described above, these batteries accumulate any energy generated. This results in cost savings as the energy produced free of charge is used later to power the lift. Our lifts also have the option of being powered by a photovoltaic panel (SOL-ARE technology), which makes the lift even more efficient and increasingly independent from the national grid.

The batteries are monitored by a system that checks their status and stops the lift when the batteries are not sufficiently charged.

If this happens during a run, the system ends the run and remains stopped at that floor while it recharges. Then, when the batteries are sufficiently charged, the system starts working normally again.

This type of situation occurs only very rarely because the batteries are sized according to a number of insertions per hour that the lift is unlikely to ever perform.

With the batteries charged and under optimal usage conditions, up to 60 runs can be made. This ensures efficient service even during a blackout.

Our SOL-ARE technology optimises battery charging using the solar energy produced by a photovoltaic panel. The system automatically selects the ideal energy source (grid or photovoltaic panel) in order to minimize the amount of energy drawn from the grid, right down to a consumption level of ZERO

The main power supply for our lifts is based on the use of lead-acid batteries, which are widely used in the automotive world. They guarantee a long service life, low costs and excellent performance. Like all batteries, they have a lifecycle, which is long and can be replaced for a limited cost.

A battery-powered lifting system guarantees high levels of energy efficiency, thanks to its low consumption of electrical energy from the national grid and its recovery system that stores energy in the batteries during operation, so it can be used in subsequent runs. From this point of view, battery power offers system users greater safety as it allows the lift to be used even in the event of a blackout.

Yes, ZEN-0 has a higher speed that can reach up to 0.8 m/s.

In this case, Switch mode* is activated, i.e. the lift’s power supply shifts from batteries to mains, and the passenger is informed with an illuminated icon. The lift moves more slowly so it remains within the parameters of the electricity meter installed until the required battery charge level is reached.

* in switch mode the power used is 1200W and 1500W during rapid recharging. These values refer to a system with a load capacity of 450kg at a speed of 0.15m/s

With the batteries charged and under optimal usage conditions, up to 40 runs can be made. This ensures efficient service even during a blackout.

Yes, all our lifts feature soft arrivals and departures. The silence achieved by our ARE SMART-POWER technology gives lift passengers a pleasant sensation of comfort throughout every run.

The main power supply for our ARE systems is based on the use of lead-acid batteries, which are widely used in the automotive world. They guarantee a long service life, low costs and excellent performance. Like all batteries, they have a lifecycle, which is long and can be replaced for a limited cost.

A battery-powered lifting system guarantees high levels of energy efficiency, thanks to its low consumption of electrical energy from the national grid and its recovery system that stores energy in the batteries during operation, so it can be used in subsequent runs. From this point of view, battery power offers system users greater safety.

Certainly! The vast range of materials and finishes available for the cabin walls and floors offers multiple customisation options. You can also choose different automatic or hinged door models to adapt the lift to the context in which it will be installed.

You can choose between two cabin models:

Monolith which has an elegant, sober design

Elegant that has an elegant, cutting-edge design

Download our MANGUSTA and ZEN-0 brochures to view all these features in detail

Yes it can, as long as the floor complies with the maximum thickness required (15 mm for the MANGUSTA lift, 10 mm for the MINIWATT lift, 20 mm for the ZEN lift)

With our lifting devices, there is no need for space to house oleodynamic control units and control panels. The motor unit is located inside the lift well and the control panel can be incorporated into a landing door.

Yes, all our lifts feature soft arrivals and departures. The silence achieved by our ARE SMART-POWER technology gives lift passengers a pleasant sensation of comfort throughout every run.

Batteries are the main power supply system used on our lifts. So our lifts can continue to be used even in the event of a sudden power failure, so accessibility and safety are guaranteed at all times.

Yes, because our MANGUSTA and MINIWATT lifts use just 130W** of power whereas the ZEN-0 lift uses only 300W.* The power used by a microwave oven is more than this (700W).

* In switch mode the power used is 1200W and 1500W during rapid recharging. These values refer to a system with a load capacity of 450kg at a speed of 0.15m/s

**In countries outside the EU the power used is 230W

Yes, our technical department can design customised solutions that meet installation requirements even in environments with limited space.

A battery-powered lifting system guarantees high levels of energy efficiency, thanks to its low consumption of electrical energy from the national grid and its recovery system that stores energy in the batteries during operation, so it can be used in subsequent runs. From this point of view, battery power offers system users greater safety.

Certainly! The vast range of materials and finishes available for the cabin walls and floors offers multiple customisation options. You can also choose different automatic or hinged door models to adapt the lift to the context in which it will be installed.

You can choose between two cabin models:

Monolith which has an elegant, sober design

Elegant that has an elegant, cutting-edge design

Download our MANGUSTA and ZEN-0 brochures to view all these features in detail

Yes it can, as long as the floor complies with the maximum thickness required (15 mm for the MANGUSTA lift, 10 mm for the MINIWATT lift, 20 mm for the ZEN lift)

With our lifting devices, there is no need for space to house oleodynamic control units and control panels. The motor unit is located inside the lift well and the control panel can be incorporated into a landing door.

Yes, all our lifts feature soft arrivals and departures. The silence achieved by our ARE SMART-POWER technology gives lift passengers a pleasant sensation of comfort throughout every run.

Batteries are the main power supply system used on our lifts. So our lifts can continue to be used even in the event of a sudden power failure, so accessibility and safety are guaranteed at all times.

Yes, because our MANGUSTA and MINIWATT lifts use just 130W* power whereas the ZEN-0 lift uses only 300W**. The power used by a microwave oven is more than this (700W).

*In countries outside the EU the power used is 230W.

**In switch mode the power used is 1200W and 1500W during rapid recharging. These values refer to a system with a load capacity of 450kg at a speed of 0.15m/s

Yes, our technical department can design customised solutions that meet installation requirements even in environments with limited space.

A battery-powered lifting system guarantees high levels of energy efficiency, thanks to its low consumption of electrical energy from the national grid and its recovery system that stores energy in the batteries during operation, so it can be used in subsequent runs. From this point of view, battery power offers system users greater safety.

Certainly! The vast range of materials and finishes available for the cabin walls and floors offers multiple customisation options. You can also choose different automatic or hinged door models to adapt the lift to the context in which it will be installed.

You can choose between two cabin models:

Monolith which has an elegant, sober design

Elegant that has an elegant, cutting-edge design

Download our MANGUSTA and ZEN-0 brochures to view all these features in detail

Yes it can, as long as the floor complies with the maximum thickness required (15 mm for the MANGUSTA lift, 10 mm for the MINIWATT lift, 20 mm for the ZEN lift)

With our lifting devices, there is no need for space to house oleodynamic control units and control panels. The motor unit is located inside the lift well and the control panel can be incorporated into a landing door.

Yes, all our lifts feature soft arrivals and departures. The silence achieved by our ARE SMART-POWER technology gives lift passengers a pleasant sensation of comfort throughout every run.

Batteries are the main power supply system used on our lifts. So our lifts can continue to be used even in the event of a sudden power failure, so accessibility and safety are guaranteed at all times.

Yes, because our MANGUSTA and MINIWATT lifts use just 130W* power whereas the ZEN-0 lift uses only 300W**. The power used by a microwave oven is more than this (700W).

*In countries outside the EU the power used is 230W